18 Years Factory Transparent Level Gauge - OR-MULTI-TUBE Series Oil Pressure Cooler – Xinyuan
18 Years Factory Transparent Level Gauge - OR-MULTI-TUBE Series Oil Pressure Cooler – Xinyuan Detail:
1. Heat transfer to determine the best cooling effect. This cooler adopts multi-tube type, large cooling area, Good cooling effect.
2. The cooling area is full. The cooling area is calculated according to the surface area of the copper tube, so the cooling area is full.
3. Cooler material is most suitable for heat dissipation. Adopt pure red copper tube, heat conductivity is above 0.95.
1. the cooling pipe oil two can freely decide the inlet and outlet, the flow of oil itself is not restricted. The inlet of water must be entered from the bottom and discharged from the upper outlet.
2. Fresh water only. The use of sea water shall be specially customized.
3. Food and chemicals must not be used.
4. water inlet and oil inlet temperature difference in more than 80°C can not be used.
5. the highest pressure: oil side 10kg/cm2, water side 7kg/cm2
6. the water side (heat transfer tube inner surface) for about 4 months or half a year, remove scale once, can maintain a good cooling efficiency. When using high viscosity oil, please keep the amount of oil equal to the amount of water.
Model | A | B | C | ΦD | E | F | G | J | K | 4>L | M | N | Traffic |
OR-60 | 450 | 305 | 46 | 90 | 120 | 3/4″ | 3/4″ | 23 | 11 | 115.5 | 95 | 7×10 | 60 |
OR-100 | 555 | 403 | 57 | 114 | 150 | 3/4″ | 3/4″ | 33 | 12.5 | 145.5 | 106.5 | 10×20 | 100 |
OR-150 | 575 | 385 | 76 | 140 | 180 | 11/4″ | 1″ | 30 | 12.5 | 175 | 130 | 13×16 | 150 |
OR-250 | 780 | 585 | 76 | 140 | 180 | 11/4″ | 1″ | 30 | 12.5 | 175 | 130 | 13×16 | 250 |
OR-350 | 1180 | 990 | 76 | 140 | 180 | 11/4″ | 1″ | 30 | 12.5 | 175 | 130 | 13×16 | 350 |
OR-600 | 1175 | 950 | 87 | 165 | 205 | T | 11/411 | 34 | 12.5 | 200 | 161 | 13×16 | 600 |
OR-800 | 1700 | 1490 | 87 | 165 | 205 | T | 11/4“ | 34 | 12.5 | 200 | 161 | 13×16 | 800 |
OR-1000 | 2140 | 1890 | 87 | 165 | 205 | T | 11/4″ | 34 | 12.5 | 200 | 161 | 13×16 | 1000 |
Model |
L |
Cl |
C |
L2 |
LI |
H2 |
B |
C2 |
n-b x I |
Hl |
D2 |
DI |
(12 |
dl |
Weight (Kg) |
SL-303 | 305 | 45 | 152 | 107 |
80 |
85 |
115 |
75 |
4-11×20 | 64 |
120 |
87.9 |
G3/4 |
G3/4 |
4.5 |
SL-304 | 377 | 224 | 179 |
5 |
|||||||||||
SL-305 | 450 | 296 | 251 | 5.5 | |||||||||||
SL-307 | 593 | 440 | 395 |
6 |
|||||||||||
SL-309 | 737 |
584 |
539 |
7 |
|||||||||||
SL-311 | 880 | 728 | 683 |
8 |
|||||||||||
SL-408 | 467 | 75 | 284 | 240 |
94 |
100 |
150 |
110 |
4-10×20 | 85 |
160 |
121 |
G1 1/4 |
G3/4 |
14 |
SL-411 | 610 | 428 | 384 |
17 |
|||||||||||
SL-415 | 755 | 572 | 528 |
19 |
|||||||||||
SL-418 | 900 | 716 | 672 |
22 |
|||||||||||
SL-421 | 1042 | 860 | 816 |
25 |
|||||||||||
SL-512 | 528 | 70 | 298 | 206 |
121 |
140 |
180 |
135 |
4-18×25 | 95 |
180 |
139.8 |
G1 1/2 |
G1 |
20 |
SL-518 | 635 | 406 | 342 |
22 |
|||||||||||
SL-526 | 852 | 622 | 558 |
27 |
|||||||||||
SL-534 | 1070 | 838 | 774 |
32 |
|||||||||||
SL-542 | 1285 |
1054 |
990 |
38 |
Note: our company can manufacture all kinds of large and special coolers according to the requirements of customers.
1. Calculate the heat required to exchange:
Q(Kcal /h) (1) Calculate according to the temperature requirements and flow of the oil: Q is CW of N dot T2.In the formula, the specific heat of C oil (kCa L/kg°C) W — the flow rate of oil (kg/h)T1 — inlet oil temperature (°C) T2 — outlet oil temperature (°C)Among them: W = qPIn the formula, Q — flow rate of oil (IV min) P — density of oil (kg/L)According to the calorific value of the hydraulic system: Q = Pr-Pc-PhcWhere, PR is the input power of the hydraulic system PHC one tank, pipe heat dissipation power PC – output effective power.
2. Select the cooler model
Check the product performance curve according to the calculated heat exchange Q and oil flow Ws, and the intersection point of the two is the selected model.
3. Supplementary Notes
The actual operating conditions of the cooler may differ from their performance test conditions. The oil viscosity is small, the water flow is large, the temperature difference between the oil temperature and the water temperature is large, the model can be selected to be smaller than the selected model, on the contrary, the model is selected to be large.
Product detail pictures:
Related Product Guide:
In order to give you convenience and enlarge our business, we also have inspectors in QC Team and assure you our best service and product for 18 Years Factory Transparent Level Gauge - OR-MULTI-TUBE Series Oil Pressure Cooler – Xinyuan , The product will supply to all over the world, such as: Italy, Swaziland, New Zealand, As a way to make use of the resource on the expanding information and facts in international trade, we welcome prospects from everywhere on the web and offline. In spite in the top quality products and solutions we supply, effective and satisfying consultation service is supplied by our professional after-sale service group. Solution lists and thorough parameters and any other info weil be sent for you timely for the inquiries. So make sure you get in touch with us by sending us emails or contact us if you have any concerns about our firm. ou can also get our address info from our web site and come to our enterprise. or a field survey of our solutions. We're confident that we have been going to share mutual results and build solid co-operation relations with our companions in this market. We're looking forward to your inquiries.
By Ida from Costa Rica - 2017.07.28 15:46
It's really lucky to find such a professional and responsible manufacturer, the product quality is good and delivery is timely, very nice.
By Elma from Sydney - 2018.08.12 12:27