Filter
-
QYLOil Return Filter For Hydraulic System
This filter is suitable for hydraulic system oil return fine filtration, filter system due to wear, metal particles and seals produced by the rubber impurities and other pollutants, so that the oil return to the tank to keep clean. The filter is directly connected with the return oil pipeline by screw thread, and extends into the oil of the oil tank. The filter element adopts a new type of chemical fiber filter material, which has the advantages of high oil permeability, high filtering precision, small pressure loss and large pollution capacity.
-
Rfb With Check Valve Magnetic Return Filter Series
RFB-series filters are used in the return line of hydraulic systems. They can be installed on the top. at the side or in the bottom of tanks. Every filter is equiped with a permanent magnet to remove ferrous matters in the oil. Filter element is made of non-woven fib re with high efficiency and low restriction. A diffuser is fitted in the lower part of the filter, ensuring steady oil flow into the tank. There is a check valve in the f- iIter to prevent oil flowing out from the tank when filter element is changed.
-
Rlf Return Line Filter Series
RLF series filter is used in return line, it can remove all the contaminants from the hydraulic system, and allow the clean oil flow back to the tank. The el ement of this series is made of glass fibre, it has high efficiency and filtration,large dirt capacity and lower initial pressure drop. There is a by -pass valve and a contamination indicator. The indicator will act when the pressure drop across filter element attains 035MPa, the element should be changed at this time. If the system can not be stopped or nobody replaces the element, the by-pass valve will open to protect the hydraulic system safety.
-
Ylx Series Return Filter On Oil Tank
This filter is suitable for hydraulic system oil return fine filtration, uses in filtering hydraulic system because of, the metal particle which the component wears produces and seals the rubber impurity and so on contaminant, causes to return to the oil tank, the oil fluid maintains the cleanness. The filter is equipped with a transmitter, by-pass valve and a dirt trap.
-
Cub Series Magnetic Millimeter Filter
1.I (mm) Specification
LThreaded
2. Flanged
Stick type
Magnetic filter -
Cub Series Magnetic Millimeter Filter For Precision Lathe
There are two models in this series. CWU-10X100B magnetic filter is used in the lubricating system of precision lathe. Filter element is made of stainless steel wire Mesh which can keep the system clean.
CWU-A25X60 filter is used in the head box of precision lathe. There is a permanent magnet in the core of element the filter, madia is made of stainless steel wire mesh.
-
With Check Valve Magnetic Suction Filter Series
The series filter have manual check valve. During maintenance, the check valve should beclosed in order to stop oil flowing out of the tank. The filter should be und er oil level when installing. If check valve hasn’t open completely, please don’t start the pump working, lest that will cause accident.
A vacuum indicator in the filter will signal when the pressure drop across the el ement reaches 0.018MPa showing that the filter should be cleaned.
-
Sdrlf Duplex Large Flow Rate Return Line Filter Series
SDRLF series filter is composed of two single Bowl filters and a 2-posi-tion 6-way directional valve. It is simple in construction and easy to use. There is a by-pass valve and a contamination indicator in it, forprotecting the hydrau lic system safety.
The feature of thisfilterallows continues operation even during element is changed forwhich is clogged by contaminants. After opening the balance valve and then turn the directional valve, theotherfilterbegins to work; the clogged element should be changed in time.
This series filter is widely used in the hydraulic systems of heavy-duty mi- ningand metallurgical machines.
-
Indicator For Filter Monitoring Differential Pressure
The CS type differential pressure transmitter is mainly used in the pipe passing thermostat. When the hydraulic system is working, the core of the superheater is gradually blocked because of the pollutants in the system, and the pressure of the inlet and outlet of the oil port produces pressure difference (that is, the pressure loss of the leakage core). When the pressure difference increases to the set value of the transmitter, the transmitter will automatically send out a signal to instruct the system operator to clean or replace the temperature core to ensure the safe operation of the system.
-
Sgf Duplex High Pressure Line Filter Series
The SGF series filter is composed of two single bowl filters, check valve, directional valve and indicator. It should be installed at outlet of the high-pressure line. The feature of this filter allows continuous operation even during replacing element, which is clogged by contaminant. When the pressure of the contaminant clogged element reaches to 0.5Mpa, the indicator gives signals showing that the element should be changed. At this time, turn the directional valve, let the other filter work, and change the clogged element. If the element can’t be changed in time until the pressure reaches to 0.6Mpa, the by-pass valve will open automatically to keep the system safety.
-
Sllf Duplex Lubrication Filter Series
SLLF series filter is composed of two single bowl filters and one 2-position 6 way directional valve. It is simple in construction and easy to use. There is a by pass valve and two contamination indicators in it, for protecting the lubricating s- ystem safety.
The feature of this filter allows continuous operation even if the clogged elem ent needs replacing for a clean one. After opening the balance valve and then tu rning the directional valve, the other filter will begin to work in the lubricating system; the clogged element should be changed at that time. This series filter is u- sed in lubricating systems of heavy duty, mining and metallurgical machines. -
Smf Duplex Middle Pressure Line Filter Series
The SMF series filter is composed of two single bowl filters, two checkvalves, directional valve and indicator. It fit the medium and low pressure hydraulic system. The feature of thisfilterallows continuous operation when changing clogged element. When the element is clogged by contaminant, the indicatorwill give signals showing that the elementshould be changed. At this time turn the directionalvalve, theotherfilterwill begin to work and then change the clogged element. Attention: 1.change the clogged element in time lest the clogged element dirt the hydraulic system.
